/* * Copyright 2018-2020 NXP * All rights reserved. * * * SPDX-License-Identifier: BSD-3-Clause */ #ifndef __HAL_UART_ADAPTER_H__ #define __HAL_UART_ADAPTER_H__ #include "fsl_common.h" #if defined(SDK_OS_FREE_RTOS) #include "FreeRTOS.h" #endif /*! * @addtogroup UART_Adapter * @{ */ /******************************************************************************* * Definitions ******************************************************************************/ /*! @brief Enable or disable UART adapter non-blocking mode (1 - enable, 0 - disable) */ #ifdef DEBUG_CONSOLE_TRANSFER_NON_BLOCKING #define UART_ADAPTER_NON_BLOCKING_MODE (1U) #else #ifndef SERIAL_MANAGER_NON_BLOCKING_MODE #define UART_ADAPTER_NON_BLOCKING_MODE (0U) #else #define UART_ADAPTER_NON_BLOCKING_MODE SERIAL_MANAGER_NON_BLOCKING_MODE #endif #endif #if defined(__GIC_PRIO_BITS) #ifndef HAL_UART_ISR_PRIORITY #define HAL_UART_ISR_PRIORITY (25U) #endif #else #if defined(configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY) #ifndef HAL_UART_ISR_PRIORITY #define HAL_UART_ISR_PRIORITY (configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY) #endif #else /* The default value 3 is used to support different ARM Core, such as CM0P, CM4, CM7, and CM33, etc. * The minimum number of priority bits implemented in the NVIC is 2 on these SOCs. The value of mininum * priority is 3 (2^2 - 1). So, the default value is 3. */ #ifndef HAL_UART_ISR_PRIORITY #define HAL_UART_ISR_PRIORITY (3U) #endif #endif #endif #ifndef HAL_UART_ADAPTER_LOWPOWER #define HAL_UART_ADAPTER_LOWPOWER (0U) #endif /* HAL_UART_ADAPTER_LOWPOWER */ /*! @brief Enable or disable uart hardware FIFO mode (1 - enable, 0 - disable) */ #ifndef HAL_UART_ADAPTER_FIFO #define HAL_UART_ADAPTER_FIFO (1U) #endif /* HAL_UART_ADAPTER_FIFO */ #if (defined(SERIAL_PORT_TYPE_UART_DMA) && (SERIAL_PORT_TYPE_UART_DMA > 0U)) #ifndef HAL_UART_DMA_ENABLE #define HAL_UART_DMA_ENABLE (1U) #endif #endif #ifndef HAL_UART_DMA_ENABLE #define HAL_UART_DMA_ENABLE (0U) #endif /* HAL_UART_DMA_ENABLE */ /*! @brief Enable or disable uart DMA adapter int mode (1 - enable, 0 - disable) */ #ifndef HAL_UART_DMA_INIT_ENABLE #define HAL_UART_DMA_INIT_ENABLE (1U) #endif /* HAL_SPI_MASTER_DMA_INIT_ENABLE */ /*! @brief Definition of uart dma adapter software idleline detection timeout value in ms. */ #ifndef HAL_UART_DMA_IDLELINE_TIMEOUT #define HAL_UART_DMA_IDLELINE_TIMEOUT (1U) #endif /* HAL_UART_DMA_IDLELINE_TIMEOUT */ /*! @brief Definition of uart adapter handle size. */ #if (defined(UART_ADAPTER_NON_BLOCKING_MODE) && (UART_ADAPTER_NON_BLOCKING_MODE > 0U)) #define HAL_UART_HANDLE_SIZE (92U + HAL_UART_ADAPTER_LOWPOWER * 16U + HAL_UART_DMA_ENABLE * 4U) #define HAL_UART_BLOCK_HANDLE_SIZE (8U + HAL_UART_ADAPTER_LOWPOWER * 16U + HAL_UART_DMA_ENABLE * 4U) #else #define HAL_UART_HANDLE_SIZE (8U + HAL_UART_ADAPTER_LOWPOWER * 16U + HAL_UART_DMA_ENABLE * 4U) #endif /*! @brief Definition of uart dma adapter handle size. */ #if (defined(HAL_UART_DMA_ENABLE) && (HAL_UART_DMA_ENABLE > 0U)) #if (defined(FSL_FEATURE_SOC_DMA_COUNT) && (FSL_FEATURE_SOC_DMA_COUNT > 0U)) #define HAL_UART_DMA_HANDLE_SIZE (124U + HAL_UART_ADAPTER_LOWPOWER * 36U) #elif (defined(FSL_FEATURE_SOC_EDMA_COUNT) && (FSL_FEATURE_SOC_EDMA_COUNT > 0U)) #define HAL_UART_DMA_HANDLE_SIZE (140U + HAL_UART_ADAPTER_LOWPOWER * 36U) #else #error This SOC does not have DMA or EDMA available! #endif #endif /* HAL_UART_DMA_ENABLE */ /*! * @brief Defines the uart handle * * This macro is used to define a 4 byte aligned uart handle. * Then use "(hal_uart_handle_t)name" to get the uart handle. * * The macro should be global and could be optional. You could also define uart handle by yourself. * * This is an example, * @code * UART_HANDLE_DEFINE(uartHandle); * @endcode * * @param name The name string of the uart handle. */ #define UART_HANDLE_DEFINE(name) uint32_t name[((HAL_UART_HANDLE_SIZE + sizeof(uint32_t) - 1U) / sizeof(uint32_t))] #if (defined(HAL_UART_DMA_ENABLE) && (HAL_UART_DMA_ENABLE > 0U)) #define UART_DMA_HANDLE_DEFINE(name) \ uint32_t name[((HAL_UART_DMA_HANDLE_SIZE + sizeof(uint32_t) - 1U) / sizeof(uint32_t))] #endif /*! @brief Whether enable transactional function of the UART. (0 - disable, 1 - enable) */ #ifndef HAL_UART_TRANSFER_MODE #define HAL_UART_TRANSFER_MODE (0U) #endif /*! @brief The handle of uart adapter. */ typedef void *hal_uart_handle_t; /*! @brief The handle of uart dma adapter. */ typedef void *hal_uart_dma_handle_t; /*! @brief UART status */ typedef enum _hal_uart_status { kStatus_HAL_UartSuccess = kStatus_Success, /*!< Successfully */ kStatus_HAL_UartTxBusy = MAKE_STATUS(kStatusGroup_HAL_UART, 1), /*!< TX busy */ kStatus_HAL_UartRxBusy = MAKE_STATUS(kStatusGroup_HAL_UART, 2), /*!< RX busy */ kStatus_HAL_UartTxIdle = MAKE_STATUS(kStatusGroup_HAL_UART, 3), /*!< HAL UART transmitter is idle. */ kStatus_HAL_UartRxIdle = MAKE_STATUS(kStatusGroup_HAL_UART, 4), /*!< HAL UART receiver is idle */ kStatus_HAL_UartBaudrateNotSupport = MAKE_STATUS(kStatusGroup_HAL_UART, 5), /*!< Baudrate is not support in current clock source */ kStatus_HAL_UartProtocolError = MAKE_STATUS( kStatusGroup_HAL_UART, 6), /*!< Error occurs for Noise, Framing, Parity, etc. For transactional transfer, The up layer needs to abort the transfer and then starts again */ kStatus_HAL_UartError = MAKE_STATUS(kStatusGroup_HAL_UART, 7), /*!< Error occurs on HAL UART */ } hal_uart_status_t; /*! @brief UART parity mode. */ typedef enum _hal_uart_parity_mode { kHAL_UartParityDisabled = 0x0U, /*!< Parity disabled */ kHAL_UartParityEven = 0x2U, /*!< Parity even enabled */ kHAL_UartParityOdd = 0x3U, /*!< Parity odd enabled */ } hal_uart_parity_mode_t; /*! @brief UART stop bit count. */ typedef enum _hal_uart_stop_bit_count { kHAL_UartOneStopBit = 0U, /*!< One stop bit */ kHAL_UartTwoStopBit = 1U, /*!< Two stop bits */ } hal_uart_stop_bit_count_t; /*! @brief UART configuration structure. */ typedef struct _hal_uart_config { uint32_t srcClock_Hz; /*!< Source clock */ uint32_t baudRate_Bps; /*!< Baud rate */ hal_uart_parity_mode_t parityMode; /*!< Parity mode, disabled (default), even, odd */ hal_uart_stop_bit_count_t stopBitCount; /*!< Number of stop bits, 1 stop bit (default) or 2 stop bits */ uint8_t enableRx; /*!< Enable RX */ uint8_t enableTx; /*!< Enable TX */ uint8_t enableRxRTS; /*!< Enable RX RTS */ uint8_t enableTxCTS; /*!< Enable TX CTS */ uint8_t instance; /*!< Instance (0 - UART0, 1 - UART1, ...), detail information please refer to the SOC corresponding RM. Invalid instance value will cause initialization failure. */ #if (defined(HAL_UART_ADAPTER_FIFO) && (HAL_UART_ADAPTER_FIFO > 0u)) uint8_t txFifoWatermark; uint8_t rxFifoWatermark; #endif } hal_uart_config_t; #if (defined(HAL_UART_DMA_ENABLE) && (HAL_UART_DMA_ENABLE > 0U)) /*! @brief UART DMA status */ typedef enum _hal_uart_dma_status { kStatus_HAL_UartDmaSuccess = 0U, kStatus_HAL_UartDmaRxIdle = (1U << 1U), kStatus_HAL_UartDmaRxBusy = (1U << 2U), kStatus_HAL_UartDmaTxIdle = (1U << 3U), kStatus_HAL_UartDmaTxBusy = (1U << 4U), kStatus_HAL_UartDmaIdleline = (1U << 5U), kStatus_HAL_UartDmaError = (1U << 6U), } hal_uart_dma_status_t; typedef struct _dma_mux_configure_t { union { struct { uint8_t dma_mux_instance; uint32_t rx_request; uint32_t tx_request; } dma_dmamux_configure; }; } dma_mux_configure_t; typedef struct _dma_channel_mux_configure_t { union { struct { uint32_t dma_rx_channel_mux; uint32_t dma_tx_channel_mux; } dma_dmamux_configure; }; } dma_channel_mux_configure_t; typedef struct _hal_uart_dma_config_t { uint8_t uart_instance; uint8_t dma_instance; uint8_t rx_channel; uint8_t tx_channel; void *dma_mux_configure; void *dma_channel_mux_configure; } hal_uart_dma_config_t; #endif /* HAL_UART_DMA_ENABLE */ /*! @brief UART transfer callback function. */ typedef void (*hal_uart_transfer_callback_t)(hal_uart_handle_t handle, hal_uart_status_t status, void *callbackParam); #if (defined(HAL_UART_DMA_ENABLE) && (HAL_UART_DMA_ENABLE > 0U)) typedef struct _dma_callback_msg { hal_uart_dma_status_t status; uint8_t *data; uint32_t dataSize; } hal_dma_callback_msg_t; /*! @brief UART transfer callback function. */ typedef void (*hal_uart_dma_transfer_callback_t)(hal_uart_dma_handle_t handle, hal_dma_callback_msg_t *msg, void *callbackParam); #endif /* HAL_UART_DMA_ENABLE */ /*! @brief UART transfer structure. */ typedef struct _hal_uart_transfer { uint8_t *data; /*!< The buffer of data to be transfer.*/ size_t dataSize; /*!< The byte count to be transfer. */ } hal_uart_transfer_t; /******************************************************************************* * API ******************************************************************************/ #if defined(__cplusplus) extern "C" { #endif /* _cplusplus */ /*! * @name Initialization and deinitialization * @{ */ /*! * @brief Initializes a UART instance with the UART handle and the user configuration structure. * * This function configures the UART module with user-defined settings. The user can configure the configuration * structure. The parameter handle is a pointer to point to a memory space of size #HAL_UART_HANDLE_SIZE allocated by * the caller. Example below shows how to use this API to configure the UART. * @code * UART_HANDLE_DEFINE(g_UartHandle); * hal_uart_config_t config; * config.srcClock_Hz = 48000000; * config.baudRate_Bps = 115200U; * config.parityMode = kHAL_UartParityDisabled; * config.stopBitCount = kHAL_UartOneStopBit; * config.enableRx = 1; * config.enableTx = 1; * config.enableRxRTS = 0; * config.enableTxCTS = 0; * config.instance = 0; * HAL_UartInit((hal_uart_handle_t)g_UartHandle, &config); * @endcode * * @param handle Pointer to point to a memory space of size #HAL_UART_HANDLE_SIZE allocated by the caller. * The handle should be 4 byte aligned, because unaligned access doesn't be supported on some devices. * You can define the handle in the following two ways: * #UART_HANDLE_DEFINE(handle); * or * uint32_t handle[((HAL_UART_HANDLE_SIZE + sizeof(uint32_t) - 1U) / sizeof(uint32_t))]; * @param config Pointer to user-defined configuration structure. * @retval kStatus_HAL_UartBaudrateNotSupport Baudrate is not support in current clock source. * @retval kStatus_HAL_UartSuccess UART initialization succeed */ hal_uart_status_t HAL_UartInit(hal_uart_handle_t handle, const hal_uart_config_t *uart_config); /*! * @brief Deinitializes a UART instance. * * This function waits for TX complete, disables TX and RX, and disables the UART clock. * * @param handle UART handle pointer. * @retval kStatus_HAL_UartSuccess UART de-initialization succeed */ hal_uart_status_t HAL_UartDeinit(hal_uart_handle_t handle); /*! @}*/ /*! * @name Blocking bus Operations * @{ */ /*! * @brief Reads RX data register using a blocking method. * * This function polls the RX register, waits for the RX register to be full or for RX FIFO to * have data, and reads data from the RX register. * * @note The function #HAL_UartReceiveBlocking and the function HAL_UartTransferReceiveNonBlocking * cannot be used at the same time. * And, the function HAL_UartTransferAbortReceive cannot be used to abort the transmission of this function. * * @param handle UART handle pointer. * @param data Start address of the buffer to store the received data. * @param length Size of the buffer. * @retval kStatus_HAL_UartError An error occurred while receiving data. * @retval kStatus_HAL_UartParityError A parity error occurred while receiving data. * @retval kStatus_HAL_UartSuccess Successfully received all data. */ hal_uart_status_t HAL_UartReceiveBlocking(hal_uart_handle_t handle, uint8_t *data, size_t length); /*! * @brief Writes to the TX register using a blocking method. * * This function polls the TX register, waits for the TX register to be empty or for the TX FIFO * to have room and writes data to the TX buffer. * * @note The function #HAL_UartSendBlocking and the function HAL_UartTransferSendNonBlocking * cannot be used at the same time. * And, the function HAL_UartTransferAbortSend cannot be used to abort the transmission of this function. * * @param handle UART handle pointer. * @param data Start address of the data to write. * @param length Size of the data to write. * @retval kStatus_HAL_UartSuccess Successfully sent all data. */ hal_uart_status_t HAL_UartSendBlocking(hal_uart_handle_t handle, const uint8_t *data, size_t length); /*! @}*/ #if (defined(UART_ADAPTER_NON_BLOCKING_MODE) && (UART_ADAPTER_NON_BLOCKING_MODE > 0U)) #if (defined(HAL_UART_TRANSFER_MODE) && (HAL_UART_TRANSFER_MODE > 0U)) /*! * @name Transactional * @note The transactional API and the functional API cannot be used at the same time. The macro * #HAL_UART_TRANSFER_MODE is used to set which one will be used. If #HAL_UART_TRANSFER_MODE is zero, the * functional API with non-blocking mode will be used. Otherwise, transactional API will be used. * @{ */ /*! * @brief Installs a callback and callback parameter. * * This function is used to install the callback and callback parameter for UART module. * When any status of the UART changed, the driver will notify the upper layer by the installed callback * function. And the status is also passed as status parameter when the callback is called. * * @param handle UART handle pointer. * @param callback The callback function. * @param callbackParam The parameter of the callback function. * @retval kStatus_HAL_UartSuccess Successfully install the callback. */ hal_uart_status_t HAL_UartTransferInstallCallback(hal_uart_handle_t handle, hal_uart_transfer_callback_t callback, void *callbackParam); /*! * @brief Receives a buffer of data using an interrupt method. * * This function receives data using an interrupt method. This is a non-blocking function, which * returns directly without waiting for all data to be received. * The receive request is saved by the UART driver. * When the new data arrives, the receive request is serviced first. * When all data is received, the UART driver notifies the upper layer * through a callback function and passes the status parameter @ref kStatus_UART_RxIdle. * * @note The function #HAL_UartReceiveBlocking and the function #HAL_UartTransferReceiveNonBlocking * cannot be used at the same time. * * @param handle UART handle pointer. * @param transfer UART transfer structure, see #hal_uart_transfer_t. * @retval kStatus_HAL_UartSuccess Successfully queue the transfer into transmit queue. * @retval kStatus_HAL_UartRxBusy Previous receive request is not finished. * @retval kStatus_HAL_UartError An error occurred. */ hal_uart_status_t HAL_UartTransferReceiveNonBlocking(hal_uart_handle_t handle, hal_uart_transfer_t *transfer); /*! * @brief Transmits a buffer of data using the interrupt method. * * This function sends data using an interrupt method. This is a non-blocking function, which * returns directly without waiting for all data to be written to the TX register. When * all data is written to the TX register in the ISR, the UART driver calls the callback * function and passes the @ref kStatus_UART_TxIdle as status parameter. * * @note The function #HAL_UartSendBlocking and the function #HAL_UartTransferSendNonBlocking * cannot be used at the same time. * * @param handle UART handle pointer. * @param transfer UART transfer structure. See #hal_uart_transfer_t. * @retval kStatus_HAL_UartSuccess Successfully start the data transmission. * @retval kStatus_HAL_UartTxBusy Previous transmission still not finished; data not all written to TX register yet. * @retval kStatus_HAL_UartError An error occurred. */ hal_uart_status_t HAL_UartTransferSendNonBlocking(hal_uart_handle_t handle, hal_uart_transfer_t *transfer); /*! * @brief Gets the number of bytes that have been received. * * This function gets the number of bytes that have been received. * * @param handle UART handle pointer. * @param count Receive bytes count. * @retval kStatus_HAL_UartError An error occurred. * @retval kStatus_Success Get successfully through the parameter \p count. */ hal_uart_status_t HAL_UartTransferGetReceiveCount(hal_uart_handle_t handle, uint32_t *count); /*! * @brief Gets the number of bytes written to the UART TX register. * * This function gets the number of bytes written to the UART TX * register by using the interrupt method. * * @param handle UART handle pointer. * @param count Send bytes count. * @retval kStatus_HAL_UartError An error occurred. * @retval kStatus_Success Get successfully through the parameter \p count. */ hal_uart_status_t HAL_UartTransferGetSendCount(hal_uart_handle_t handle, uint32_t *count); /*! * @brief Aborts the interrupt-driven data receiving. * * This function aborts the interrupt-driven data receiving. The user can get the remainBytes to know * how many bytes are not received yet. * * @note The function #HAL_UartTransferAbortReceive cannot be used to abort the transmission of * the function #HAL_UartReceiveBlocking. * * @param handle UART handle pointer. * @retval kStatus_Success Get successfully abort the receiving. */ hal_uart_status_t HAL_UartTransferAbortReceive(hal_uart_handle_t handle); /*! * @brief Aborts the interrupt-driven data sending. * * This function aborts the interrupt-driven data sending. The user can get the remainBytes to find out * how many bytes are not sent out. * * @note The function #HAL_UartTransferAbortSend cannot be used to abort the transmission of * the function #HAL_UartSendBlocking. * * @param handle UART handle pointer. * @retval kStatus_Success Get successfully abort the sending. */ hal_uart_status_t HAL_UartTransferAbortSend(hal_uart_handle_t handle); /*! @}*/ #else /*! * @name Functional API with non-blocking mode. * @note The functional API and the transactional API cannot be used at the same time. The macro * #HAL_UART_TRANSFER_MODE is used to set which one will be used. If #HAL_UART_TRANSFER_MODE is zero, the * functional API with non-blocking mode will be used. Otherwise, transactional API will be used. * @{ */ /*! * @brief Installs a callback and callback parameter. * * This function is used to install the callback and callback parameter for UART module. * When non-blocking sending or receiving finished, the adapter will notify the upper layer by the installed callback * function. And the status is also passed as status parameter when the callback is called. * * @param handle UART handle pointer. * @param callback The callback function. * @param callbackParam The parameter of the callback function. * @retval kStatus_HAL_UartSuccess Successfully install the callback. */ hal_uart_status_t HAL_UartInstallCallback(hal_uart_handle_t handle, hal_uart_transfer_callback_t callback, void *callbackParam); /*! * @brief Receives a buffer of data using an interrupt method. * * This function receives data using an interrupt method. This is a non-blocking function, which * returns directly without waiting for all data to be received. * The receive request is saved by the UART adapter. * When the new data arrives, the receive request is serviced first. * When all data is received, the UART adapter notifies the upper layer * through a callback function and passes the status parameter @ref kStatus_UART_RxIdle. * * @note The function #HAL_UartReceiveBlocking and the function #HAL_UartReceiveNonBlocking * cannot be used at the same time. * * @param handle UART handle pointer. * @param data Start address of the data to write. * @param length Size of the data to write. * @retval kStatus_HAL_UartSuccess Successfully queue the transfer into transmit queue. * @retval kStatus_HAL_UartRxBusy Previous receive request is not finished. * @retval kStatus_HAL_UartError An error occurred. */ hal_uart_status_t HAL_UartReceiveNonBlocking(hal_uart_handle_t handle, uint8_t *data, size_t length); /*! * @brief Transmits a buffer of data using the interrupt method. * * This function sends data using an interrupt method. This is a non-blocking function, which * returns directly without waiting for all data to be written to the TX register. When * all data is written to the TX register in the ISR, the UART driver calls the callback * function and passes the @ref kStatus_UART_TxIdle as status parameter. * * @note The function #HAL_UartSendBlocking and the function #HAL_UartSendNonBlocking * cannot be used at the same time. * * @param handle UART handle pointer. * @param data Start address of the data to write. * @param length Size of the data to write. * @retval kStatus_HAL_UartSuccess Successfully start the data transmission. * @retval kStatus_HAL_UartTxBusy Previous transmission still not finished; data not all written to TX register yet. * @retval kStatus_HAL_UartError An error occurred. */ hal_uart_status_t HAL_UartSendNonBlocking(hal_uart_handle_t handle, uint8_t *data, size_t length); /*! * @brief Gets the number of bytes that have been received. * * This function gets the number of bytes that have been received. * * @param handle UART handle pointer. * @param count Receive bytes count. * @retval kStatus_HAL_UartError An error occurred. * @retval kStatus_Success Get successfully through the parameter \p count. */ hal_uart_status_t HAL_UartGetReceiveCount(hal_uart_handle_t handle, uint32_t *reCount); /*! * @brief Gets the number of bytes written to the UART TX register. * * This function gets the number of bytes written to the UART TX * register by using the interrupt method. * * @param handle UART handle pointer. * @param count Send bytes count. * @retval kStatus_HAL_UartError An error occurred. * @retval kStatus_Success Get successfully through the parameter \p count. */ hal_uart_status_t HAL_UartGetSendCount(hal_uart_handle_t handle, uint32_t *seCount); /*! * @brief Aborts the interrupt-driven data receiving. * * This function aborts the interrupt-driven data receiving. The user can get the remainBytes to know * how many bytes are not received yet. * * @note The function #HAL_UartAbortReceive cannot be used to abort the transmission of * the function #HAL_UartReceiveBlocking. * * @param handle UART handle pointer. * @retval kStatus_Success Get successfully abort the receiving. */ hal_uart_status_t HAL_UartAbortReceive(hal_uart_handle_t handle); /*! * @brief Aborts the interrupt-driven data sending. * * This function aborts the interrupt-driven data sending. The user can get the remainBytes to find out * how many bytes are not sent out. * * @note The function #HAL_UartAbortSend cannot be used to abort the transmission of * the function #HAL_UartSendBlocking. * * @param handle UART handle pointer. * @retval kStatus_Success Get successfully abort the sending. */ hal_uart_status_t HAL_UartAbortSend(hal_uart_handle_t handle); /*! @}*/ #endif #endif #if (defined(HAL_UART_DMA_ENABLE) && (HAL_UART_DMA_ENABLE > 0U)) /*! * @brief Initializes a UART dma instance with the UART dma handle and the user configuration structure. * * This function configures the UART dma module with user-defined settings. The user can configure the configuration * structure. The parameter handle is a pointer to point to a memory space of size #HAL_UART_DMA_HANDLE_SIZE allocated * by the caller. Example below shows how to use this API to configure the UART. * @code * * Init TimerManager, only used in UART without Idleline interrupt * timer_config_t timerConfig; * timerConfig.srcClock_Hz = 16000000; * timerConfig.instance = 0; * TM_Init(&timerConfig); * * Init the DMA module * DMA_Init(DMA0); * * Define a uart dma handle * UART_HANDLE_DEFINE(g_uartHandle); * UART_DMA_HANDLE_DEFINE(g_UartDmaHandle); * * Configure uart settings * hal_uart_config_t uartConfig; * uartConfig.srcClock_Hz = 48000000; * uartConfig.baudRate_Bps = 115200; * uartConfig.parityMode = kHAL_UartParityDisabled; * uartConfig.stopBitCount = kHAL_UartOneStopBit; * uartConfig.enableRx = 1; * uartConfig.enableTx = 1; * uartConfig.enableRxRTS = 0; * uartConfig.enableTxCTS = 0; * uartConfig.instance = 0; * * Init uart * HAL_UartInit((hal_uart_handle_t *)g_uartHandle, &uartConfig); * * Configure uart dma settings * hal_uart_dma_config_t dmaConfig; * dmaConfig.uart_instance = 0; * dmaConfig.dma_instance = 0; * dmaConfig.rx_channel = 0; * dmaConfig.tx_channel = 1; * * Init uart dma * HAL_UartDMAInit((hal_uart_handle_t *)g_uartHandle, (hal_uart_dma_handle_t *)g_uartDmaHandle, &dmaConfig); * @endcode * * @param handle UART handle pointer. * @param dmaHandle Pointer to point to a memory space of size #HAL_UART_DMA_HANDLE_SIZE allocated by the caller. * The handle should be 4 byte aligned, because unaligned access doesn't be supported on some devices. * You can define the handle in the following two ways: * #UART_DMA_HANDLE_DEFINE(handle); * or * uint32_t handle[((HAL_UART_DMA_HANDLE_SIZE + sizeof(uint32_t) - 1U) / sizeof(uint32_t))]; * @param dmaConfig Pointer to user-defined configuration structure. * @retval kStatus_HAL_UartDmaError UART dma initialization failed. * @retval kStatus_HAL_UartDmaSuccess UART dma initialization succeed. */ hal_uart_dma_status_t HAL_UartDMAInit(hal_uart_handle_t handle, hal_uart_dma_handle_t dmaHandle, hal_uart_dma_config_t *dmaConfig); /*! * @brief Deinitializes a UART DMA instance. * * This function will abort uart dma receive/send transfer and deinitialize UART. * * @param handle UART handle pointer. * @retval kStatus_HAL_UartDmaSuccess UART DMA de-initialization succeed */ hal_uart_dma_status_t HAL_UartDMADeinit(hal_uart_handle_t handle); /*! * @brief Installs a callback and callback parameter. * * This function is used to install the callback and callback parameter for UART DMA module. * When any status of the UART DMA changed, the driver will notify the upper layer by the installed callback * function. And the status is also passed as status parameter when the callback is called. * * @param handle UART handle pointer. * @param callback The callback function. * @param callbackParam The parameter of the callback function. * @retval kStatus_HAL_UartDmaSuccess Successfully install the callback. */ hal_uart_dma_status_t HAL_UartDMATransferInstallCallback(hal_uart_handle_t handle, hal_uart_dma_transfer_callback_t callback, void *callbackParam); /*! * @brief Receives a buffer of data using an dma method. * * This function receives data using an dma method. This is a non-blocking function, which * returns directly without waiting for all data to be received. * The receive request is saved by the UART DMA driver. * When all data is received, the UART DMA adapter notifies the upper layer * through a callback function and passes the status parameter @ref kStatus_HAL_UartDmaRxIdle. * * When an idleline is detected, the UART DMA adapter notifies the upper layer through a callback function, * and passes the status parameter @ref kStatus_HAL_UartDmaIdleline. For the UARTs without hardware idleline * interrupt(like usart), it will use a software idleline detection method with the help of TimerManager. * * When the soc support cache, uplayer should do cache maintain operations for transfer buffer before call this API. * * @param handle UART handle pointer. * @param data data Start address of the buffer to store the received data. * @param length Size of the buffer. * @param receiveAll Idleline interrupt will not end transfer process if set true. * @retval kStatus_HAL_UartDmaSuccess Successfully start the data receive. * @retval kStatus_HAL_UartDmaRxBusy Previous receive request is not finished. */ hal_uart_dma_status_t HAL_UartDMATransferReceive(hal_uart_handle_t handle, uint8_t *data, size_t length, bool receiveAll); /*! * @brief Transmits a buffer of data using an dma method. * * This function sends data using an dma method. This is a non-blocking function, which * returns directly without waiting for all data to be written to the TX register. When * all data is written to the TX register by DMA, the UART DMA driver calls the callback * function and passes the @ref kStatus_HAL_UartDmaTxIdle as status parameter. * * When the soc support cache, uplayer should do cache maintain operations for transfer buffer before call this API. * * @param handle UART handle pointer. * @param data data Start address of the data to write. * @param length Size of the data to write. * @retval kStatus_HAL_UartDmaSuccess Successfully start the data transmission. * @retval kStatus_HAL_UartDmaTxBusy Previous send request is not finished. */ hal_uart_dma_status_t HAL_UartDMATransferSend(hal_uart_handle_t handle, uint8_t *data, size_t length); /*! * @brief Gets the number of bytes that have been received. * * This function gets the number of bytes that have been received. * * @param handle UART handle pointer. * @param reCount Receive bytes count. * @retval kStatus_HAL_UartDmaError An error occurred. * @retval kStatus_HAL_UartDmaSuccess Get successfully through the parameter \p reCount. */ hal_uart_dma_status_t HAL_UartDMAGetReceiveCount(hal_uart_handle_t handle, uint32_t *reCount); /*! * @brief Gets the number of bytes written to the UART TX register. * * This function gets the number of bytes written to the UART TX * register by using the DMA method. * * @param handle UART handle pointer. * @param count Send bytes count. * @retval kStatus_HAL_UartDmaError An error occurred. * @retval kStatus_HAL_UartDmaSuccess Get successfully through the parameter \p seCount. */ hal_uart_dma_status_t HAL_UartDMAGetSendCount(hal_uart_handle_t handle, uint32_t *seCount); /*! * @brief Aborts the DMA-driven data receiving. * * This function aborts the DMA-driven data receiving. * * @param handle UART handle pointer. * @retval kStatus_HAL_UartDmaSuccess Get successfully abort the receiving. */ hal_uart_dma_status_t HAL_UartDMAAbortReceive(hal_uart_handle_t handle); /*! * @brief Aborts the DMA-driven data sending. * * This function aborts the DMA-driven data sending. * * @param handle UART handle pointer. * @retval kStatus_Success Get successfully abort the sending. */ hal_uart_dma_status_t HAL_UartDMAAbortSend(hal_uart_handle_t handle); #endif /* HAL_UART_DMA_ENABLE */ /*! * @brief Prepares to enter low power consumption. * * This function is used to prepare to enter low power consumption. * * @param handle UART handle pointer. * @retval kStatus_HAL_UartSuccess Successful operation. * @retval kStatus_HAL_UartError An error occurred. */ hal_uart_status_t HAL_UartEnterLowpower(hal_uart_handle_t handle); /*! * @brief Restores from low power consumption. * * This function is used to restore from low power consumption. * * @param handle UART handle pointer. * @retval kStatus_HAL_UartSuccess Successful operation. * @retval kStatus_HAL_UartError An error occurred. */ hal_uart_status_t HAL_UartExitLowpower(hal_uart_handle_t handle); #if (defined(UART_ADAPTER_NON_BLOCKING_MODE) && (UART_ADAPTER_NON_BLOCKING_MODE > 0U)) /*! * @brief UART IRQ handle function. * * This function handles the UART transmit and receive IRQ request. * * @param handle UART handle pointer. */ void HAL_UartIsrFunction(hal_uart_handle_t handle); #endif #if defined(__cplusplus) } #endif /*! @}*/ #endif /* __HAL_UART_ADAPTER_H__ */