// Copyright (c) 2022 Cesanta Software Limited // All rights reserved // https://www.st.com/resource/en/reference_manual/dm00031020-stm32f405-415-stm32f407-417-stm32f427-437-and-stm32f429-439-advanced-arm-based-32-bit-mcus-stmicroelectronics.pdf #pragma once #include #include #include #include #include #define BIT(x) (1UL << (x)) #define SETBITS(R, CLEARMASK, SETMASK) (R) = ((R) & ~(CLEARMASK)) | (SETMASK) #define PIN(bank, num) ((((bank) - 'A') << 8) | (num)) #define PINNO(pin) (pin & 255) #define PINBANK(pin) (pin >> 8) #define LED1 PIN('B', 0) // On-board LED pin (green) #define LED2 PIN('B', 7) // On-board LED pin (blue) #define LED3 PIN('B', 14) // On-board LED pin (red) #define LED LED2 // Use blue LED for blinking // System clock // 6.3.3: APB1 clock <= 45MHz; APB2 clock <= 90MHz // 3.5.1, Table 11: configure flash latency (WS) in accordance to clock freq // 33.4: The AHB clock must be at least 25 MHz when Ethernet is used enum { APB1_PRE = 5 /* AHB clock / 4 */, APB2_PRE = 4 /* AHB clock / 2 */ }; enum { PLL_HSI = 16, PLL_M = 8, PLL_N = 168, PLL_P = 2, PLL_Q = 7 }; #define FLASH_LATENCY 5 #define SYS_FREQUENCY ((PLL_HSI * PLL_N / PLL_M / PLL_P) * 1000000) // Core 168 MHz, USB 48 MHz #define APB2_FREQUENCY (SYS_FREQUENCY / (BIT(APB2_PRE - 3))) #define APB1_FREQUENCY (SYS_FREQUENCY / (BIT(APB1_PRE - 3))) static inline void spin(volatile uint32_t count) { while (count--) (void) 0; } enum { GPIO_MODE_INPUT, GPIO_MODE_OUTPUT, GPIO_MODE_AF, GPIO_MODE_ANALOG }; enum { GPIO_OTYPE_PUSH_PULL, GPIO_OTYPE_OPEN_DRAIN }; enum { GPIO_SPEED_LOW, GPIO_SPEED_MEDIUM, GPIO_SPEED_HIGH, GPIO_SPEED_INSANE }; enum { GPIO_PULL_NONE, GPIO_PULL_UP, GPIO_PULL_DOWN }; #define GPIO(N) ((GPIO_TypeDef *) (0x40020000 + 0x400 * (N))) static GPIO_TypeDef *gpio_bank(uint16_t pin) { return GPIO(PINBANK(pin)); } static inline void gpio_toggle(uint16_t pin) { GPIO_TypeDef *gpio = gpio_bank(pin); uint32_t mask = BIT(PINNO(pin)); gpio->BSRR = mask << (gpio->ODR & mask ? 16 : 0); } static inline int gpio_read(uint16_t pin) { return gpio_bank(pin)->IDR & BIT(PINNO(pin)) ? 1 : 0; } static inline void gpio_write(uint16_t pin, bool val) { GPIO_TypeDef *gpio = gpio_bank(pin); gpio->BSRR = BIT(PINNO(pin)) << (val ? 0 : 16); } static inline void gpio_init(uint16_t pin, uint8_t mode, uint8_t type, uint8_t speed, uint8_t pull, uint8_t af) { GPIO_TypeDef *gpio = gpio_bank(pin); uint8_t n = (uint8_t) (PINNO(pin)); RCC->AHB1ENR |= BIT(PINBANK(pin)); // Enable GPIO clock SETBITS(gpio->OTYPER, 1UL << n, ((uint32_t) type) << n); SETBITS(gpio->OSPEEDR, 3UL << (n * 2), ((uint32_t) speed) << (n * 2)); SETBITS(gpio->PUPDR, 3UL << (n * 2), ((uint32_t) pull) << (n * 2)); SETBITS(gpio->AFR[n >> 3], 15UL << ((n & 7) * 4), ((uint32_t) af) << ((n & 7) * 4)); SETBITS(gpio->MODER, 3UL << (n * 2), ((uint32_t) mode) << (n * 2)); } static inline void gpio_input(uint16_t pin) { gpio_init(pin, GPIO_MODE_INPUT, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, GPIO_PULL_NONE, 0); } static inline void gpio_output(uint16_t pin) { gpio_init(pin, GPIO_MODE_OUTPUT, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, GPIO_PULL_NONE, 0); } static inline void irq_exti_attach(uint16_t pin) { uint8_t bank = (uint8_t) (PINBANK(pin)), n = (uint8_t) (PINNO(pin)); SYSCFG->EXTICR[n / 4] &= ~(15UL << ((n % 4) * 4)); SYSCFG->EXTICR[n / 4] |= (uint32_t) (bank << ((n % 4) * 4)); EXTI->IMR |= BIT(n); EXTI->RTSR |= BIT(n); EXTI->FTSR |= BIT(n); int irqvec = n < 5 ? 6 + n : n < 10 ? 23 : 40; // IRQ vector index, 10.1.2 NVIC_SetPriority(irqvec, 3); NVIC_EnableIRQ(irqvec); } #ifndef UART_DEBUG #define UART_DEBUG USART3 #endif static inline void uart_init(USART_TypeDef *uart, unsigned long baud) { // https://www.st.com/resource/en/datasheet/stm32f429zi.pdf uint8_t af = 7; // Alternate function uint16_t rx = 0, tx = 0; // pins uint32_t freq = 0; // Bus frequency. UART1 is on APB2, rest on APB1 if (uart == USART1) freq = APB2_FREQUENCY, RCC->APB2ENR |= BIT(4); if (uart == USART2) freq = APB1_FREQUENCY, RCC->APB1ENR |= BIT(17); if (uart == USART3) freq = APB1_FREQUENCY, RCC->APB1ENR |= BIT(18); if (uart == USART1) tx = PIN('A', 9), rx = PIN('A', 10); if (uart == USART2) tx = PIN('A', 2), rx = PIN('A', 3); if (uart == USART3) tx = PIN('D', 8), rx = PIN('D', 9); gpio_init(tx, GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, 0, af); gpio_init(rx, GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, 0, af); uart->CR1 = 0; // Disable this UART uart->BRR = freq / baud; // Set baud rate uart->CR1 |= BIT(13) | BIT(2) | BIT(3); // Set UE, RE, TE } static inline void uart_write_byte(USART_TypeDef *uart, uint8_t byte) { uart->DR = byte; while ((uart->SR & BIT(7)) == 0) spin(1); } static inline void uart_write_buf(USART_TypeDef *uart, char *buf, size_t len) { while (len-- > 0) uart_write_byte(uart, *(uint8_t *) buf++); } static inline int uart_read_ready(USART_TypeDef *uart) { return uart->SR & BIT(5); // If RXNE bit is set, data is ready } static inline uint8_t uart_read_byte(USART_TypeDef *uart) { return (uint8_t) (uart->DR & 255); } static inline void usb_init() { gpio_init(PIN('A', 11), GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, GPIO_PULL_NONE, 10); // D+ gpio_init(PIN('A', 12), GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, GPIO_PULL_NONE, 10); // D- gpio_init(PIN('A', 9), GPIO_MODE_INPUT, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, GPIO_PULL_NONE, 0); // VBUS gpio_init(PIN('A', 10), GPIO_MODE_AF, GPIO_OTYPE_OPEN_DRAIN, GPIO_SPEED_HIGH, GPIO_PULL_UP, 10); // ID RCC->AHB2ENR |= RCC_AHB2ENR_OTGFSEN; // Enable USB FS clock USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_NOVBUSSENS; // VBUS sensing disable USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN; // VBUS sensing enable } static inline void rng_init(void) { RCC->AHB2ENR |= RCC_AHB2ENR_RNGEN; RNG->CR |= RNG_CR_RNGEN; } static inline uint32_t rng_read(void) { while ((RNG->SR & RNG_SR_DRDY) == 0) (void) 0; return RNG->DR; } #define UUID ((uint8_t *) UID_BASE) // Unique 96-bit chip ID. TRM 39.1 // Helper macro for MAC generation #define GENERATE_LOCALLY_ADMINISTERED_MAC() \ { \ 2, UUID[0] ^ UUID[1], UUID[2] ^ UUID[3], UUID[4] ^ UUID[5], \ UUID[6] ^ UUID[7] ^ UUID[8], UUID[9] ^ UUID[10] ^ UUID[11] \ }