mirror of
https://github.com/cesanta/mongoose.git
synced 2024-12-15 18:09:15 +08:00
83 lines
3.4 KiB
C
83 lines
3.4 KiB
C
// Copyright (c) 2022 Cesanta Software Limited
|
|
// All rights reserved
|
|
|
|
#include "mcu.h"
|
|
#include "mongoose.h"
|
|
|
|
#define LED1 PIN('B', 0) // On-board LED pin (green)
|
|
#define LED2 PIN('B', 7) // On-board LED pin (blue)
|
|
#define LED3 PIN('B', 14) // On-board LED pin (red)
|
|
#define BTN1 PIN('C', 13) // On-board user button
|
|
|
|
static uint64_t s_ticks, s_exti; // Counters, increased by IRQ handlers
|
|
|
|
static void blink_cb(void *arg) { // Blink periodically
|
|
// MG_INFO(("ticks: %u", (unsigned) s_ticks));
|
|
gpio_toggle(LED2);
|
|
(void) arg;
|
|
}
|
|
|
|
uint64_t mg_millis(void) { // Declare our own uptime function
|
|
return s_ticks; // Return number of milliseconds since boot
|
|
}
|
|
|
|
void HardFault_Handler(void) { // Escalated fault handler
|
|
gpio_output(LED3); // Setup red LED
|
|
for (;;) spin(2999999), gpio_toggle(LED3); // Blink LED infinitely
|
|
}
|
|
|
|
void SysTick_Handler(void) { // SyStick IRQ handler, triggered every 1ms
|
|
s_ticks++;
|
|
}
|
|
|
|
void EXTI15_10_IRQHandler(void) { // External interrupt handler
|
|
s_exti++;
|
|
if (EXTI->PR & BIT(PINNO(BTN1))) EXTI->PR = BIT(PINNO(BTN1));
|
|
gpio_write(LED1, gpio_read(BTN1)); // No debounce. Turn LED if button pressed
|
|
}
|
|
|
|
int main(void) {
|
|
static struct uart *uart = UART3; // Use UART3 - its attached to debug
|
|
clock_init(); // Set clock to 180MHz
|
|
systick_init(FREQ / 1000); // Increment s_ticks every ms
|
|
gpio_output(LED1); // Setup green LED
|
|
gpio_output(LED2); // Setup blue LED
|
|
gpio_input(BTN1); // Set button to input
|
|
irq_exti_attach(BTN1); // Attach BTN1 to exti
|
|
uart_init(uart, 115200); // It is wired to the debug port
|
|
|
|
// Initialise Ethernet. Enable MAC GPIO pins, see
|
|
// https://www.farnell.com/datasheets/2014265.pdf section 6.10
|
|
uint16_t pins[] = {PIN('A', 1), PIN('A', 2), PIN('A', 7),
|
|
PIN('B', 13), PIN('C', 1), PIN('C', 4),
|
|
PIN('C', 5), PIN('G', 11), PIN('G', 13)};
|
|
for (size_t i = 0; i < sizeof(pins) / sizeof(pins[0]); i++) {
|
|
gpio_init(pins[i], GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_INSANE,
|
|
GPIO_PULL_NONE, 11);
|
|
}
|
|
nvic_enable_irq(61); // Setup Ethernet IRQ handler
|
|
RCC->APB2ENR |= BIT(14); // Enable SYSCFG
|
|
SYSCFG->PMC |= BIT(23); // Use RMII. Goes first!
|
|
RCC->AHB1ENR |= BIT(25) | BIT(26) | BIT(27); // Enable Ethernet clocks
|
|
RCC->AHB1RSTR |= BIT(25); // ETHMAC force reset
|
|
RCC->AHB1RSTR &= ~BIT(25); // ETHMAC release reset
|
|
|
|
struct mg_mgr mgr; // Initialise Mongoose event manager
|
|
mg_mgr_init(&mgr); // and attach it to the MIP interface
|
|
mg_log_set(MG_LL_DEBUG); // Set log level
|
|
mg_timer_add(&mgr, 500, MG_TIMER_REPEAT, blink_cb, &mgr);
|
|
|
|
// Initialise Mongoose network stack
|
|
// Specify MAC address, and use 0 for IP, mask, GW - i.e. use DHCP
|
|
// For static configuration, specify IP/mask/GW in network byte order
|
|
struct mip_cfg c = {.mac = {0, 0, 1, 2, 3, 4}, .ip = 0, .mask = 0, .gw = 0};
|
|
mip_init(&mgr, &c, &mip_driver_stm32, NULL);
|
|
MG_INFO(("Init done, starting main loop"));
|
|
|
|
extern void device_dashboard_fn(struct mg_connection *, int, void *, void *);
|
|
mg_http_listen(&mgr, "http://0.0.0.0", device_dashboard_fn, &mgr);
|
|
for (;;) mg_mgr_poll(&mgr, 0); // Infinite event loop
|
|
|
|
return 0;
|
|
}
|