mirror of
https://github.com/cesanta/mongoose.git
synced 2024-12-14 00:31:42 +08:00
68 lines
3.1 KiB
C
68 lines
3.1 KiB
C
// Copyright (c) 2023 Cesanta Software Limited
|
|
// All rights reserved
|
|
//
|
|
// This file contains essentials required by the CMSIS:
|
|
// uint32_t SystemCoreClock - holds the system core clock value
|
|
// SystemInit() - initialises the system, e.g. sets up clocks
|
|
|
|
#include "hal.h"
|
|
|
|
uint32_t SystemCoreClock = SYS_FREQUENCY;
|
|
|
|
// - 14.4, Figure 14-2: clock tree
|
|
// - 14.7.4: ARM_PODF defaults to /2
|
|
// - 14.7.5: AHB_PODF defaults to /1; IPG_PODF defaults to /4; PERIPH_CLK_SEL
|
|
// defaults to derive clock from pre_periph_clk_sel
|
|
// - 14.7.6: PRE_PERIPH_CLK_SEL defaults to derive clock from divided PLL1.
|
|
// - (For 528MHz operation, we need to set it to derive clock from PLL2).
|
|
// - 14.6.1.3.1 ARM PLL (PLL1); 13.3.2.2 PLLs
|
|
// - 14.8.1: PLL1 is powered off and bypassed to 24MHz. Fout = 24MHz *
|
|
// div_select/2
|
|
// - For 600MHz operation, we need to set PLL1 on
|
|
// - Datasheet 4.1.3: System frequency/Bus frequency max 600/150MHz respectively
|
|
// (AHB/IPG)
|
|
// - MCUXpresso: IPG_CLK_ROOT <= 150MHz; PERCLK_CLK_ROOT <= 75MHz
|
|
// - Datasheet 4.9.4.1.1/2: the processor clock frequency must exceed twice the
|
|
// ENET_RX_CLK/ENET_TX_CLK frequency.
|
|
// - Datasheet 4.9.4.2: no details for RMII (above is for MII), assumed 50MHz
|
|
// min processor clock
|
|
// - Datasheet 4.1.3, Table 10: "Overdrive" run mode requires 1.25V core voltage
|
|
// minimum; 528 MHz does not.
|
|
void SystemInit(void) { // Called automatically by startup code (ints masked)
|
|
SCB->CPACR |= ((3UL << 10 * 2) | (3UL << 11 * 2)); // Enable FPU
|
|
asm("DSB");
|
|
asm("ISB");
|
|
// 53.4.2: Disable watchdog after reset (unlocked)
|
|
RTWDOG->CS &= ~RTWDOG_CS_EN_MASK;
|
|
RTWDOG->TOVAL = 0xFFFF;
|
|
while (RTWDOG->CS & RTWDOG_CS_ULK_MASK) spin(1); // wait for lock
|
|
while ((RTWDOG->CS & RTWDOG_CS_RCS_MASK) == 0)
|
|
spin(1); // wait for new config
|
|
// Set VDD_SOC to 1.25V
|
|
SETBITS(DCDC->REG3, DCDC_REG3_TRG_MASK, DCDC_REG3_TRG(0x12));
|
|
while ((DCDC->REG0 & DCDC_REG0_STS_DC_OK_MASK) == 0)
|
|
spin(1); // Wait for DCDC_STS_DC_OK
|
|
SETBITS(CCM->CSCMR1, CCM_CSCMR1_PERCLK_PODF_MASK,
|
|
CCM_CSCMR1_PERCLK_PODF(1)); // Set PERCLK divider /2 (75MHz)
|
|
// Set clock to 600 MHz. Power PLL on and configure divider
|
|
SETBITS(CCM_ANALOG->PLL_ARM,
|
|
CCM_ANALOG_PLL_ARM_POWERDOWN_MASK |
|
|
CCM_ANALOG_PLL_ARM_SET_DIV_SELECT_MASK,
|
|
CCM_ANALOG_PLL_ARM_SET_DIV_SELECT(100));
|
|
while ((CCM_ANALOG->PLL_ARM & CCM_ANALOG_PLL_ARM_LOCK_MASK) == 0)
|
|
spin(1); // wait until it is stable
|
|
CCM_ANALOG->PLL_ARM &=
|
|
~CCM_ANALOG_PLL_ARM_BYPASS_MASK; // Disable Bypass (switch to PLL)
|
|
// 14.5 Table 14-4: uart_clk_root
|
|
// 14.4: uart_clk_root = PLL3/6 or OSC; CCM_CSCDR1 (14.7.9) defaults to
|
|
// PLL3/6/1
|
|
CCM_ANALOG->PLL_USB1 |= CCM_ANALOG_PLL_USB1_POWER_MASK; // Power PLL on
|
|
while ((CCM_ANALOG->PLL_USB1 & CCM_ANALOG_PLL_USB1_LOCK_MASK) == 0)
|
|
spin(1); // wait until it is stable
|
|
CCM_ANALOG->PLL_USB1 &=
|
|
~CCM_ANALOG_PLL_USB1_BYPASS_MASK; // Disable Bypass (switch to PLL)
|
|
rng_init(); // Initialise random number generator
|
|
// NXP startup code calls SystemInit BEFORE initializing RAM...
|
|
SysTick_Config(SYS_FREQUENCY / 1000); // Sys tick every 1ms
|
|
}
|