The SSL_OP_ENABLE_MIDDLEBOX_COMPAT option is provided by QuicTLS and enabled
by default in the newly created SSL contexts. SSL_set_quic_method() is used
to clear it, which is required for SSL handshake to work on QUIC connections.
Switching context in the ngx_http_ssl_servername() SNI callback overrides SSL
options from the new SSL context. This results in the option set again.
Fix is to explicitly clear it when switching to another SSL context.
Initially reported here (in Russian):
http://mailman.nginx.org/pipermail/nginx-ru/2021-November/063989.html
ngx_http_v3_tables.h and ngx_http_v3_tables.c are renamed to
ngx_http_v3_table.h and ngx_http_v3_table.c to better match HTTP/2 code.
ngx_http_v3_streams.h and ngx_http_v3_streams.c are renamed to
ngx_http_v3_uni.h and ngx_http_v3_uni.c to better match their content.
Directives that set transport parameters are removed from the configuration.
Corresponding values are derived from the quic configuration or initialized
to default. Whenever possible, quic configuration parameters are taken from
higher-level protocol settings, i.e. HTTP/3.
A new variable $http3 is added. The variable equals to "h3" for HTTP/3
connections, "hq" for hq connections and is an empty string otherwise.
The variable $quic is eliminated.
The new variable is similar to $http2 variable.
RFC 9000 19.16
The sequence number specified in a RETIRE_CONNECTION_ID frame MUST NOT
refer to the Destination Connection ID field of the packet in which the
frame is contained.
Before the patch, the RETIRE_CONNECTION_ID frame was sent before switching
to the new client id. If retired client id was currently in use, this lead
to violation of the spec.
The c->udp->dgram may be NULL only if the quic connection was just
created: the ngx_event_udp_recvmsg() passes information about datagrams
to existing connections by providing information in c->udp.
If case of a new connection, c->udp is allocated by the QUIC code during
creation of quic connection (it uses c->sockaddr to initialize qsock->path).
Thus the check for qsock->path is excessive and can be read wrong, assuming
that other options possible, leading to warnings from clang static analyzer.
Removed sending CLOSE_CONNECTION directly to avoid duplicate frames,
since it is sent later again in SSL_do_handshake() error handling.
As such, removed redundant settings of error fields set elsewhere.
While here, improved debug message.
All open sockets are stored in a queue. There is no need to close some
of them separately. If it happens that active and backup point to same
socket, double close may happen (leading to possible segfault).
The RFC 9000 allows a packet from known CID arrive from unknown path:
These requirements regarding connection ID reuse apply only to the
sending of packets, as unintentional changes in path without a change
in connection ID are possible. For example, after a period of
network inactivity, NAT rebinding might cause packets to be sent on a
new path when the client resumes sending.
Before the patch, such packets were rejected with an error in the
ngx_quic_check_migration() function. Removing the check makes the
separate function excessive - remaining checks are early migration
check and "disable_active_migration" check. The latter is a transport
parameter sent to client and it should not be used by server.
The server should send "disable_active_migration" "if the endpoint does
not support active connection migration" (18.2). The support status depends
on nginx configuration: to have migration working with multiple workers,
you need bpf helper, available on recent Linux systems. The patch does
not set "disable_active_migration" automatically and leaves it for the
administrator. By default, active migration is enabled.
RFC 900 says that it is ok to migrate if the peer violates
"disable_active_migration" flag requirements:
If the peer violates this requirement,
the endpoint MUST either drop the incoming packets on that path without
generating a Stateless Reset
OR
proceed with path validation and allow the peer to migrate. Generating a
Stateless Reset or closing the connection would allow third parties in the
network to cause connections to close by spoofing or otherwise manipulating
observed traffic.
So, nginx adheres to the second option and proceeds to path validation.
Note:
The ngtcp2 may be used for testing both active migration and NAT rebinding:
ngtcp2/client --change-local-addr=200ms --delay-stream=500ms <ip> <port> <url>
ngtcp2/client --change-local-addr=200ms --delay-stream=500ms --nat-rebinding \
<ip> <port> <url>
Single UDP datagram may contain multiple QUIC datagrams. In order to
facilitate handling of such cases, 'first' flag in the ngx_quic_header_t
structure is introduced.
Previously, the retired socket was not closed if it didn't match
active or backup.
New sockets could not be created (due to count limit), since retired socket
was not closed before calling ngx_quic_create_sockets().
When replacing retired socket, new socket is only requested after closing
old one, to avoid hitting the limit on the number of active connection ids.
Together with added restrictions, this fixes an issue when a current socket
could be closed during migration, recreated and erroneously reused leading
to null pointer dereference.
Previously the frame was not handled and connection was closed with an error.
Now, after receiving this frame, global flow control is updated and new
flow control credit is sent to client.
Previously, after receiving STREAM_DATA_BLOCKED, current flow control limit
was sent to client. Now, if the limit can be updated to the full window size,
it is updated and the new value is sent to client, otherwise nothing is sent.
The change lets client update flow control credit on demand. Also, it saves
traffic by not sending MAX_STREAM_DATA with the same value twice.
The reasons why a stream may not be created by server currently include hitting
worker_connections limit and memory allocation error. Previously in these
cases the entire QUIC connection was closed and all its streams were shut down.
Now the new stream is rejected and existing streams continue working.
To reject an HTTP/3 request stream, RESET_STREAM and STOP_SENDING with
H3_REQUEST_REJECTED error code are sent to client. HTTP/3 uni streams and
Stream streams are not rejected.
The variable contains a negotiated curve used for the handshake key
exchange process. Known curves are listed by their names, unknown
ones are shown in hex.
Note that for resumed sessions in TLSv1.2 and older protocols,
$ssl_curve contains the curve used during the initial handshake,
while in TLSv1.3 it contains the curve used during the session
resumption (see the SSL_get_negotiated_group manual page for
details).
The variable is only meaningful when using OpenSSL 3.0 and above.
With older versions the variable is empty.
Without this change, aio used with HTTP/2 can result in connection hang,
as observed with "aio threads; aio_write on;" and proxying (ticket #2248).
The problem is that HTTP/2 updates buffers outside of the output filters
(notably, marks them as sent), and then posts a write event to call
output filters. If a filter does not call the next one for some reason
(for example, because of an AIO operation in progress), this might
result in a state when the owner of a buffer already called
ngx_chain_update_chains() and can reuse the buffer, while the same buffer
is still sitting in the busy chain of some other filter.
In the particular case a buffer was sitting in output chain's ctx->busy,
and was reused by event pipe. Output chain's ctx->busy was permanently
blocked by it, and this resulted in connection hang.
Fix is to change ngx_chain_update_chains() to skip buffers from other
modules unconditionally, without trying to wait for these buffers to
become empty.
The "sendfile_max_chunk" directive is important to prevent worker
monopolization by fast connections. The 2m value implies maximum 200ms
delay with 100 Mbps links, 20ms delay with 1 Gbps links, and 2ms on
10 Gbps links. It also seems to be a good value for disks.
Previously, connections to upstream servers used sendfile() if it was
enabled, but never honored sendfile_max_chunk. This might result
in worker monopolization for a long time if large request bodies
are allowed.
On Linux starting with 2.6.16, sendfile() silently limits all operations
to MAX_RW_COUNT, defined as (INT_MAX & PAGE_MASK). This incorrectly
triggered the interrupt check, and resulted in 0-sized writev() on the
next loop iteration.
Fix is to make sure the limit is always checked, so we will return from
the loop if the limit is already reached even if number of bytes sent is
not exactly equal to the number of bytes we've tried to send.
Previously, it was checked that sendfile_max_chunk was enabled and
almost whole sendfile_max_chunk was sent (see e67ef50c3176), to avoid
delaying connections where sendfile_max_chunk wasn't reached (for example,
when sending responses smaller than sendfile_max_chunk). Now we instead
check if there are unsent data, and the connection is still ready for writing.
Additionally we also check c->write->delayed to ignore connections already
delayed by limit_rate.
This approach is believed to be more robust, and correctly handles
not only sendfile_max_chunk, but also internal limits of c->send_chain(),
such as sendfile() maximum supported length (ticket #1870).
Previously, 1 millisecond delay was used instead. In certain edge cases
this might result in noticeable performance degradation though, notably on
Linux with typical CONFIG_HZ=250 (so 1ms delay becomes 4ms),
sendfile_max_chunk 2m, and link speed above 2.5 Gbps.
Using posted next events removes the artificial delay and makes processing
fast in all cases.
The directive enables including all frames from start time to the most recent
key frame in the result. Those frames are removed from presentation timeline
using mp4 edit lists.
Edit lists are currently supported by popular players and browsers such as
Chrome, Safari, QuickTime and ffmpeg. Among those not supporting them properly
is Firefox[1].
Based on a patch by Tracey Jaquith, Internet Archive.
[1] https://bugzilla.mozilla.org/show_bug.cgi?id=1735300
The function updates the duration field of mdhd atom. Previously it was
updated in ngx_http_mp4_read_mdhd_atom(). The change makes it possible to
alter track duration as a result of processing track frames.
As per quic-qpack-21:
When a stream is reset or reading is abandoned, the decoder emits a
Stream Cancellation instruction.
Previously the instruction was not sent. Now it's sent when closing QUIC
stream connection if dynamic table capacity is non-zero and eof was not
received from client. The latter condition means that a trailers section
may still be on its way from client and the stream needs to be cancelled.
A QUIC stream connection is treated as reusable until first bytes of request
arrive, which is also when the request object is now allocated. A connection
closed as a result of draining, is reset with the error code
H3_REQUEST_REJECTED. Such behavior is allowed by quic-http-34:
Once a request stream has been opened, the request MAY be cancelled
by either endpoint. Clients cancel requests if the response is no
longer of interest; servers cancel requests if they are unable to or
choose not to respond.
When the server cancels a request without performing any application
processing, the request is considered "rejected." The server SHOULD
abort its response stream with the error code H3_REQUEST_REJECTED.
The client can treat requests rejected by the server as though they had
never been sent at all, thereby allowing them to be retried later.
When an HTTP/3 function returns an error in context of a QUIC stream, it's
this function's responsibility now to finalize the entire QUIC connection
with the right code, if required. Previously, QUIC connection finalization
could be done both outside and inside such functions. The new rule follows
a similar rule for logging, leads to cleaner code, and allows to provide more
details about the error.
While here, a few error cases are no longer treated as fatal and QUIC connection
is no longer finalized in these cases. A few other cases now lead to
stream reset instead of connection finalization.
The PATH_RESPONSE frame must be expanded to 1200, except the case
when anti-amplification limit is in effect, i.e. on unvalidated paths.
Previously, the anti-amplification limit was always applied.
