14 KiB
MIP TCP / IP stack over pcap
This example allows to use Mongoose's MIP built-in TCP/IP stack on systems
that support pcap API, i.e. have libpcap library installed. The application
opens an interface and uses pcap_next_ex() for reading packets from the
interface, and pcap_inject() to write packets to the interface.
NOTE: depending on the libcap implementation, the injected packets may or may not be looped back to the interface's TCP/IP stack. If they are not looped back, then it is necessary to create a separate interface that is bridged to the target interface - see MacOS example below.
MacOS setup
MacOS has support for feth (fake ethernet) interfaces. One can create a pair
of feth interfaces and interlink them. Once a feth interface is assigned
a peer and an IP address, anything that gets injected to it, appears on a
peer interface and vice versa.
$ sudo ifconfig feth0 create
$ sudo ifconfig feth1 create
$ sudo ifconfig feth1 peer feth 0 # Link two fake ethernet ifaces together
$ sudo ifconfig feth1 10.10 # Assign 10.0.0.10 to feth1
$ sudo ifconfig feth0 up
$ sudo ifconfig feth1 up
Now we have two Ethernet interfaces, feth0 and feth1, interlinked and
active. On your Mac, go to "System Preferences" / Sharing, enable "Internet
Sharing" and choose "Thunderbolt bridge". This enables DHCP on the bridge0
interface, which is bridge for all Thunderbolt devices, and adds necessary
routes to the WiFi interface. On my system it gets 192.168.2.1 IP address,
and serves 192.168.2/24 net. We should add one of our fake interfaces to
this bridge:
$ sudo ifconfig bridge0 addm feth1
We can start an example using the feth0:
$ make -C examples/mip-pcap/ clean all ARGS="-i feth0"
...
2386718 3 mip.c:279:arp_cache_add ARP cache: added 0xc0a80201 @ 36:77:4d:be:e0:80
2386718 2 mip.c:300:onstatechange READY, IP: 192.168.2.17
The diagram of the setup is below:
┌──────────► 192.168.2.1 bridge0
│ routing DHCP │
│ ┌──────────────────┴──────────────────┐
▼ │ │ 192.168.2.17
│ ┌─────────┐ fake ethernet pair ┌─────────┐
192.168.0.10 │ │ feth1 ├────────────┬───────┤ feth0 │
┌─────────┐ │ └─────────┘ │ └────┬────┘
│ en0 │ │ │ │
└────┬────┘ │ ┌─────────┐ ┌─────────┐ ┌─────────┐ │ │
│ │ │ en1 │ │ en2 │ │ en3 │ │ mip-pcap
│ └────┬────┘ └────┬────┘ └────┬────┘ │
WiFi │ │ │ │ │
└──────┼───────────┼───────────┼──────┘
│ │ │ │
▼
Internet Thunderbolt Ethernet
Linux setup
The quick and simple options are:
- Open your loopback device (probably
lo), in which case MIP is only reachable from your machine, and MIP also sees echoes of its own traffic. - Open your Ethernet/WiFi device (probably
eth0orenpXsYfor Ethernet), in which case MIP can access the network and the Internet but is not reachable from within your machine - If you happen to have a virtual bridge interface (for linking several virtual machines together, for example) (probably
br0orvirbr0), you can open it, but it will behave as opening the underlying physical interface.
For best results, you should create a virtual interface, which you can use as is, attach to a virtual bridge, or forward/masquerade its traffic.
$ sudo ip link add my0 type veth peer [name] my1
$ sudo ip link set my0 up
$ sudo ip link set my1 up
In some systems, like for example RHEL7, name is mandatory; in others you might need not to add it, that is why we represented it here using square brackets.
Use a virtual interface
This is similar to using the loopback device, MIP is only reachable from the hosting machine, but you can add forwarding and masquerading later. Once you have your virtual interface up and running with an IP address, you can configure any services on one end, let's say my1, while you open the other end, my0 with MIP.
- Add an IP address to one end of the pipe
$ sudo ip addr add 192.168.0.1/24 dev my1 - Start your DHCP server at that interface serving that subnet, or otherwise configure MIP to use a fixed address within that subnet.
- Now start the example opening the other end of the virtual interface:
$ make -C examples/mip-pcap/ clean all ARGS="-i my0"- In some systems, you will probably need superuser privileges to open the device:
$ sudo examples/mip-pcap/example -i my0
- In some systems, you will probably need superuser privileges to open the device:
[DHCP server for 192.168.0.x]
192.168.0.1 192.168.0.x
┌─────────┐ virtual eth pair ┌─────────┐
│ my1 ├────────────────────┤ my0 │
└─────────┘ └────┬────┘
│
│
mip-pcap
As you can't access any other host than your workstation, you need to add any required services (as DNS) there, and configure Mongoose appropriately. This is a foundation, you can expand it by choosing one of the solutions that follow.
Bridge to your network
We will attach one end of the virtual interface to a bridge, which will also be attached to your network interface. In this case, MIP will have access to your network (and through it, to the Internet) and will also be reachable from your own workstation and other hosts in your network. You don't need to add IP addresses as in the example above, unless you don't have a DHCP server in your network, in which case you will configure MIP for a fixed address in your subnet.
- If you don't already have a virtual bridge interface, as mentioned above, you'll have to create it and attach your network interface (NIC) to it. Your IP address has to be assigned to the bridge, instead of the NIC. If you are using DHCP, the client must run on the bridge interface instead of the NIC.
Check using$ ip link add virbr0 type bridge $ sudo ip link set virbr0 up $ sudo ip addr del 10.1.0.10/24 dev enp9s0 $ sudo ip link set enp9s0 master virbr0 $ sudo ip addr add 10.1.0.10/24 dev virbr0ifconfig, and try to ping some host in your network - Attach one end of the virtual interface to the bridge:
$ sudo ip link set my1 master virbr0 - If everything is fine, you'll see your interface pair state is UP:
$ ip link show master virbr0 2: enp9s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master virbr0 state UP mode DEFAULT group default qlen 1000 link/ether 30:5a:3a:08:db:90 brd ff:ff:ff:ff:ff:ff 396: my1@my0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master virbr0 state UP mode DEFAULT group default qlen 1000 link/ether b6:ee:bc:53:f2:6e brd ff:ff:ff:ff:ff:ff - Now start the example opening the other end of the virtual interface:
$ make -C examples/mip-pcap/ clean all ARGS="-i my0"- In some systems, you will probably need superuser privileges to open the device:
$ sudo examples/mip-pcap/example -i my0
- In some systems, you will probably need superuser privileges to open the device:
10.1.0.10
virbr0
│
┌──────────────────┴──────────────────┐
│ │ 10.1.0.x
│ ┌─────────┐ virtual eth pair ┌─────────┐
│ │ my1 ├────────────┬───────┤ my0 │
│ └─────────┘ │ └────┬────┘
│ │ │
│ ┌─────────┐ ┌─────────┐ ┌─────────┐ │ │
│ │ vnet1 │ │ enp9s0 │ │ vnet2 │ │ mip-pcap
│ └────┬────┘ └────┬────┘ └────┬────┘ │
│ │ │ │ │
└──────┼───────────┼───────────┼──────┘
│ │ │
│
Ethernet [WiFi]
│ Local LAN 10.1.0.x
│ DHCP server, router
▼
Internet
If you have Docker running, it may introduce firewall rules that will disrupt your bridging.
Forward/Masquerade
Once you have your virtual interface up and running with an IP address, you can use your Linux to NAT and forward MIP traffic to another interface, for example the one that connects you to the Internet. In this case, MIP will have access to the Internet and will also be reachable from your own workstation; but not from any other hosts in your local network (if there is one). You can use this setup with a direct connection to the Internet or being part of a network, when you want to isolate MIP from the rest of your network.
- We assume you already have a firewall in place (you should); to configure masquerading and forwarding do:
Remember to use the proper network interface name$ sudo iptables -t nat -A POSTROUTING -o enp9s0 -j MASQUERADE $ echo 1 | sudo tee /proc/sys/net/ipv4/ip_forward - Now start the example opening the other end of the virtual interface:
$ make -C examples/mip-pcap/ clean all ARGS="-i my0"- In some systems, you will probably need superuser privileges to open the device:
$ sudo examples/mip-pcap/example -i my0
- In some systems, you will probably need superuser privileges to open the device:
[DHCP server for 192.168.0.x]
┌────────────► 192.168.0.1 192.168.0.x
│ forwarding ┌─────────┐ virtual eth pair ┌─────────┐
│ masquerading │ my1 ├────────────────────┤ my0 │
│ └─────────┘ └────┬────┘
▼ │
Your IP (LAN / Public) │
┌─────────┐ mip-pcap
│ enp9s0 │
└────┬────┘
│
│
Ethernet
│
▼
Internet
You can also use this setup if your NIC is part of a bridge (for example: you have virtual machines); in that case:
- use the bridge interface for masquerading, instead of the Ethernet (your IP now belongs to the virtual bridge, not the NIC):
Remember to use the proper bridge interface name$ sudo iptables -t nat -A POSTROUTING -o virbr0 -j MASQUERADE $ echo 1 | sudo tee /proc/sys/net/ipv4/ip_forward
[DHCP server for 192.168.0.x]
10.1.0.10 ◀──────────────► 192.168.0.1 192.168.0.x
virbr0 forwarding ┌─────────┐ virtual eth pair ┌─────────┐
│ masquerading │ my1 ├────────────────────┤ my0 │
│ └─────────┘ └────┬────┘
┌──────────────────┴──────────────────┐ │
│ │ │
│ ┌─────────┐ ┌─────────┐ ┌─────────┐ │ mip-pcap
│ │ vnet1 │ │ enp9s0 │ │ vnet2 │ │
│ └────┬────┘ └────┬────┘ └────┬────┘ │
│ │ │ │ │
└──────┼───────────┼───────────┼──────┘
│ │ │
│
Ethernet [WiFi]
│ Local LAN 10.1.0.x
│ DHCP server, router
▼
Internet